HomeAbout Us
 

 

 

Project Photos

Custom Stamping

Acid Stain

Color Flake

Exposed Aggregate

Resoration & Maintenance
Specifications
 

 

 

ULTRA SURFACE ACID STAIN

DESCRIPTION: Ultra Surface Acid Stains enhance new and existing concrete by adding a variegated, translucent coloring effect to the surface. These coloring effects are a result of a unique formulation of blended acidic metallic salts. Ultra Surface acid stains become a part of the concrete surface wearing only as the concrete wears. Because of the nature of acid stains the coloring may vary throughout the job and the final results cannot be guaranteed. It is always recommended to do a small test area to determine the final color before starting the installation. For floors in need of repairs or resurfacing, it is recommended to apply Ultra Surface Resurfacer followed by Ultra Surface Spray-Top before acid staining .

TYPICAL USES: Ultra Surface Acid Stains are available in nine standard colors and are used to provide variegated and translucent coloring effects to regular concrete and polymer concrete surfaces. They can be used straight out of the container or diluted from 1 part up to 20 parts water to achieve lighter or darker shades of color and applied in one or more coats. They can also be mixed together or applied over different colors of Ultra Surface Spray-Top to create your own unique colors.
CAUTIONS: DANGER! OXIDIZER! CORROSIVE! EYE AND SKIN BURNS! CAUSES SEVERE EYE AND SKIN IRRITATION-BLINDNESS! MAY BE FATAL IF SWALLOWED, INHALED OR ABSORBED THROUGH SKIN! PROLONGED OR REPEATED BREATHING MIGHT CAUSE ULCERATION OR PERFORATION OF NASAL MEMBRANES. CAN CAUSE CANCER, CANCER HAZARD DEPENDS ON THE LEVEL OF EXPOSURE AND DURATION. KEEP OUT OF REACH OF CHILDREN! FOR PROFESSIONAL USE ONLY! DO NOT USE UNLESS WEARING A P100/HYDROGEN CHLORIDE RESPIRATOR NIOSH TC-84A. WEAR PROTECTIVE CLOTHING – GOGGLES – GLOVES – CHEMICAL RESISTANT APRON AND BOOTS.

STAMPED CONCRETE SEALER
Technical Information
Properties of Stamped Concrete Sealer
Coverage Rate 200-300 sq. ft./gal
Solids Content, by Weight 28%
Dry to Touch (70 degrees) 30-60 minutes
Walk-on time 4-6 hours
V.O.C. (Regular version) 580 grams/liter
V.O.C. (VOC version) 400 grams/liter
Tukon Hardness 16
Adhesion to concrete concrete fails before
sealer
Chemical Resistance
Chemical resistance of Ultra Surface Stamped Concrete Sealer
is good against oil, grease and most other common chemicals
encountered in residential and some commercial environments.
Concrete Solutions recommends each client conduct their own
specific test to determine suitability of this or any other product
for their particular application.
Slip Resistance: Ultra Surface Stamped Concrete
Sealer can become slippery when wet especially on smooth
surfaces. It is up to the end user to determine the suitability of
the Stamped Concrete Sealer for their particular application.
Slip resistant granules such as glass beads or #80-100 white
aluminum oxide granules can be incorporated into the wet
Stamped Concrete Sealer to provide whatever degree of slip
resistance is necessary. Concrete Solutions or its sales agents
will not be responsible for injury incurred in a slip fall situation.
Health Hazards - Use with adequate ventilation, wear
gloves to avoid contact with skin, use the proper cartridge type
respirator in confined areas. Read Material Safety Data Sheet
prior to use.
Application Temperature - 50 degrees F
or above.

ULTRA SURFACE PATCHING MIX
DESCRIPTION: Ultra Surface Patching Mix is a special “Just Add Water” blend of cement, sand, Ultra Surface Powder Polymer and other ingredients used as a patching material for a variety of applications. It is used to repair holes and spalls; as a leveling coat to fill in low areas or to make a rough surface smooth; as a repitching coat to correct the slope for proper drainage; as an underlayment for carpet, tile or other types of flooring; to patch stucco and masonry, to eliminate tripping hazards at joints where one side of a concrete slab is raised, as well as other repair and resurfacing applications. It can be applied from less than 1/16 of an inch to 1/2 of an inch thick and feathered to zero. It is also used to make repairs, when needed, prior to applying an Ultra Surface Polymer Concrete resurfacing, texturing or 1/4" stamping application. It can even be used as a 1/4 -1/2" stamping material for samples or small jobs.


 

Copyright © 2008

  Phone Number